Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (179.43 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 6.86 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (8.73%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 99.90% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 99.90% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 3.96%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (8.48%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (8.45%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 1 / 4 ] Affinity stability is lower than 90% (30.36%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.28%) lower than cumulative innermost loop coverage (8.45%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 3 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 613 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.51 % | |
| ►Control Flow Issues | 349 | |
| ○ | [SA] Too many paths (343 paths) - Simplify control structure. There are 343 issues ( = paths) costing 1 point each with a malus of 4 points. | 347 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 349 | |
| ○ | [SA] Too many paths (343 paths) - Simplify control structure. There are 343 issues ( = paths) costing 1 point each with a malus of 4 points. | 347 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 120 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 2 issues ( = indirect data accesses) costing 4 point each. | 8 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 2 issues ( = indirect data accesses) costing 4 point each. | 8 |
| ○Loop 92 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop 1005 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.82 % | |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 2096 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
[ 4 / 4 ] Application profile is long enough (109.01 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 5.65 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (7.96%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 199.26% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 99.72% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 3.12%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (7.33%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (7.72%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (59.62%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.25%) lower than cumulative innermost loop coverage (7.72%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 3 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 2857 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.75 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 613 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 2873 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.93 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 732 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.88 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 7 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (68.24 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 4.59 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (6.75%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 391.85% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 98.15% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 2.36%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (6.17%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (6.56%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (53.84%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.19%) lower than cumulative innermost loop coverage (6.56%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 613 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 2857 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.75 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Loop 2873 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.93 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
[ 4 / 4 ] Application profile is long enough (55.47 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 2.99 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (5.45%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 723.21% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 90.66% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.26%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (4.95%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (5.32%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 4 ] Affinity stability is lower than 90% (84.98%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.13%) lower than cumulative innermost loop coverage (5.32%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 2037 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % |
[ 4 / 4 ] Application profile is long enough (37.68 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 2.17 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (4.15%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 1457.16% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 91.36% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 0.73%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (3.70%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (4.01%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 4 ] Affinity stability is lower than 90% (85.85%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.15%) lower than cumulative innermost loop coverage (4.01%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
[ 4 / 4 ] Application profile is long enough (32.01 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 1.30 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (3.14%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 2961.81% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 92.80% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 0.45%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (2.76%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (3.02%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 4 ] Affinity stability is lower than 90% (88.04%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.13%) lower than cumulative innermost loop coverage (3.02%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1728 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (27.49 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 1.44 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (2.33%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 6051.14% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 94.85% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 0.46%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (2.04%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (2.21%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 4 / 4 ] Affinity is good (91.37%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.12%) lower than cumulative innermost loop coverage (2.21%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1728 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Loop 1726 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
[ 4 / 4 ] Application profile is long enough (27.72 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.37 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (2.07%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 12128.17% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 95.21% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 0.53%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (1.87%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (1.98%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 4 / 4 ] Affinity is good (95.13%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.09%) lower than cumulative innermost loop coverage (1.98%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1728 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1726 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1504 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.48 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % |
[ 4 / 4 ] Application profile is long enough (28.42 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information
Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present.
Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 0 / 3 ] Compilation of some functions is not optimized for the target processor
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.27 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (2.08%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 16278.67% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 94.97% of time
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 0.61%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (1.92%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (2.00%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 4 / 4 ] Affinity is good (93.87%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.08%) lower than cumulative innermost loop coverage (2.00%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1728 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Loop 1726 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 1504 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.48 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |